This article was created at the special request of special forces, on the one hand to carry out a covert approach and on the other hand to be able to observe in camouflage. At the same time, access to the equipment should be quick, quiet and unhindered. An anatomically cut hood is attached to the cape, which can be fixed to the head by means of elastic drawstrings, so that it follows all movements and does not restrict the view. A face veil attached to the hood can be attached to an optronic device by means of an elastic band without hindering its operation or being blown down by the wind. Due to its extra light design, it is possible to observe through the face veil, at the same time the hole shadow between the observer and the optronics is reduced. The back part can be buttoned off and can be used separately as a small camouflage net, so the top can be used as a light camouflage jacket. The back part can also be buttoned to the front of the cape, so you can completely camouflage yourself to the front while watching. The fixable hand cuffs are directly integrated and identical to the PYTHON Gauntlets G1, these can be used with or without gloves. All outer edges, including the hood, are specially contour-breaking with a wavy edge, which minimizes telltale cast shadows. Details: Multiple adjustable hood. Closure on the chest with two large slotted buttons. Sleeves with fixable hand cuffs. Contour breaking wave edge to minimize drop shadows. Buttoned camouflage net (110x110cm) to hide the back or chest area One size. Weight: approx. 650 g. PHANTOMLEAF® has developed a new type of mesh material especially for the needs of Special Forces: the PYTHON product line. The target points were: Complete camouflage in the visual and near infrared regions of the electromagnetic spectrum. Reduced gloss level and low noise. Inherently flame retardant. Very tear-resistant and tightly woven: less entanglement in thorns and a barrier against vectors (disease-transmitting organisms). Extra light and small in pack size. Low water absorption and quick drying. So far, the PHANTOMLEAF® products have only been supplied to special units in the military and police at home and abroad. Their effect has been proven in action there. Due to the diverse demand, PHANTOMLEAF® has decided to also offer camouflage patterns for sale. The result is the WASP II camouflage pattern, which combines an exclusive look with striking camouflage quality: Unique breaking of the silhouette. In combination with complex structural algorithms. Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distance and this in front of a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This considerably expands the user's freedom of action. PHANTOMLEAF® has developed a system of camouflage schemes that is consistently modular and coordinated for worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grass and scrubland and in places rock and scree. WASP II in the color variant Z3A (tall growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forests, but also tropical jungles with a high level of adaptability for border areas such as bush and agricultural land or grass zones. WASP II in color variant Z3b (tall stature with snow cover) for use in regions with vegetation and rocks and an interrupted snow cover. WASP II in the color variant Z4 (construction) for use in humanly changed surroundings from urban terrain to large vehicles such as ships, aircraft and trains to special scenarios such as drilling rigs. 100% made in Germany.   Material:100% Polyester (inhärent FR PES).   

This item was created at the special request of special forces, on the one hand to carry out a covert approach, and then observe camouflaged. At the same time, access to the equipment should be fast, quiet and unhindered. An anatomically cut hood is attached to the cape, which can be fixed to the head by means of elastic drawstrings, so that it follows all movements and does not restrict the view. A face veil attached in the hood can be attached to optronic equipment by means of an elastic band, without hindering its operation or being blown down by the wind. Its extra-light design allows observation through the face veil while reducing the pinhole shadow between the observer and optronics. The back part can be unbuttoned and thus used separately as a small camouflage net, thus the top part can be used as a light camouflage jacket. The back part can also be buttoned to the front of the cap, thus allowing complete camouflage when observing to the front. The fixable hand gauntlets are directly integrated and identical in construction to the PYTHON Gauntlets G1, these can be used with or without gloves. All outer edges, including the hood, have an extra contour-breaking wave edge, which minimizes telltale drop shadows. The follow-up generation G2 is distinguished by the fact that it is equipped with a specially developed slit band. This slit tape is designed to provide very tear-resistant pick-up points for the 3D elements (PHANTOMLEAF® PYTHON LEAVES imitation leaves #430180) at the correct distance and angle to the base article on the one hand - but on the other hand minimizes entanglement in vegetation. Details: Slash tape for attaching camouflage material. Multi-adjustable hood. Closure on the chest with two large slotted button. sleeves with fixable hand cuffs. Contour breaking scalloped edge to minimize drop shadows. Buttonable camouflage net (110x110cm) for camouflaging the back or chest area One size fits all. Weight: approx. 650 g. Especially for the needs of special forces PHANTOMLEAF® has developed a new type of net material: The PYTHON product line. Target points were: Complete camouflage in the visual range and near-infrared range of the electromagnetic spectrum. Reduced gloss and noise. Inherently flame retardant. Very tear resistant and tightly woven: less entanglement in thorns and barrier to vectors (disease-carrying creatures). At the same time extra light and small in pack size. Low water absorption and quick drying. So far, PHANTOMLEAF® products have been supplied exclusively to special military and police units in Germany and abroad. There, their effectiveness has been proven in action. Due to the great demand, PHANTOMLEAF® has decided to also offer camouflage patterns for free sale The result is the WASP II camouflage pattern, which combines an exclusive look with breakthrough camouflage quality Unique silhouette breaking. In combination with complex structural algorithms Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distances, against a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This greatly expands the user's scope of action. PHANTOMLEAF® has developed a consistently modular system of camouflage schemes that are coordinated with each other and with worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grassland and scrubland, and in places rock and scree. WASP II in color variant Z3A (high growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forest but also tropical jungle with a high adaptability for border areas, such as scrub and agricultural land or grass zones. WASP II in color variant Z3b (high growth with snow cover) for application in regions with vegetation and rock and an interrupted snow cover. WASP II in color variant Z4 (construction) for use in human-altered environments ranging from urban terrain to large vehicles such as ships, airplanes and trains to special scenarios such as oil rigs. 100% made in Germany.   Material:100% Polyester (inhärent FR PES)   

The PHANTOMLEAF® PYTHON ASSAULTER GHILLIE GEN1 is made of a new type of mesh material and is intended to cover the most prominent parts of the body: head, shoulders and upper back, including a small backpack. The PYTHON ASSAULTER GHILLIE GEN1 is cut in such a way that it offers plenty of room for movement and access to the plate carrier and equipment. The hood has anatomically placed cords for an optimal fit. With a traction system, it can be adjusted so that it follows head movements and enables unrestricted vision. The specially rounded edges minimize treacherous shadows and help to break the contours. With the buttons open, it can also be used as a small camouflage net to cover the body or equipment. The PYTHON ASSAULTER GHILLIE GEN1 can simply be rolled up into the hood for storage. Details: Multiple adjustable hood. Closure on the chest with a large slotted button. Sleeve openings each with a large slotted button. Rounded cut edges to minimize cast shadows. One size fits all. Back length: approx. 104 cm. Weight: approx. 220 g. PHANTOMLEAF® has developed a new type of mesh material especially for the needs of Special Forces: the PYTHON product line. The target points were: Complete camouflage in the visual and near infrared regions of the electromagnetic spectrum. Reduced gloss level and low noise. Inherently flame retardant. Very tear-resistant and tightly woven: less entanglement in thorns and a barrier against vectors (disease-transmitting organisms). Extra light and small in pack size. Low water absorption and quick drying. So far, the PHANTOMLEAF® products have only been supplied to special units in the military and police at home and abroad. Their effect has been proven in action there. Due to the diverse demand, PHANTOMLEAF® has decided to also offer camouflage patterns for sale. The result is the WASP II camouflage pattern, which combines an exclusive look with striking camouflage quality: Unique breaking of the silhouette. In combination with complex structural algorithms. Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distance and this in front of a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This considerably expands the user's freedom of action. PHANTOMLEAF® has developed a system of camouflage schemes that is consistently modular and coordinated for worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grass and scrubland and in places rock and scree. WASP II in the color variant Z3A (tall growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forests, but also tropical jungles with a high level of adaptability for border areas such as bush and agricultural land or grass zones. WASP II in color variant Z3b (tall stature with snow cover) for use in regions with vegetation and rocks and an interrupted snow cover. WASP II in the color variant Z4 (construction) for use in humanly changed surroundings from urban terrain to large vehicles such as ships, aircraft and trains to special scenarios such as drilling rigs. 100% made in Germany.   Material:Netzmaterial: 100% Polyester (inhärent FR PES).   

The PHANTOMLEAF® PYTHON ASSAULTER GHILLIE GEN2 is made of a new type of mesh material, and is designed to cover the most prominent body parts: head, shoulders and upper back, including a small backpack. The PYTHON ASSAULTER GHILLIE GEN2 is cut to provide plenty of room for movement and access to plate carriers and gear. The hood has anatomically placed cords for an optimal fit. A pull system allows it to be adjusted to follow head movements and provide unrestricted vision. The specially rounded cut edges minimize treacherous drop shadows and help break up the contours. With the buttons open, it can also be used as a small camouflage net to cover the body or equipment. For storage, the PYTHON ASSAULTER GHILLIE GEN2 can be easily rolled up into the hood. The follow-up generation G2 is characterized by the fact that it is equipped with a specially designed slit band. This slit tape is designed to provide, on the one hand, very tear-resistant pick-up points for the 3D elements (PHANTOMLEAF® PYTHON LEAVES imitation leaves #430180) at the correct distance and angle to the base article - but, on the other hand, to minimize entanglement in vegetation. Details: Slash tape for attaching camouflage material. Multi-adjustable hood. Closure on the chest with a large slotted button. sleeve vents each with a large slotted button. Rounded cut edges to minimize drop shadows. One size fits all. Back length: approx. 104 cm. Weight: approx. 480 g. Note: The imitation leaves are not included! The picture only shows an example of use Especially for the needs of special forces PHANTOMLEAF® has developed a new type of mesh material: The PYTHON product line. Target points were: Complete camouflage in the visual range and near-infrared range of the electromagnetic spectrum. Reduced gloss and noise. Inherently flame retardant. Very tear resistant and tightly woven: less entanglement in thorns and barrier to vectors (disease-carrying creatures). At the same time extra light and small in pack size. Low water absorption and quick drying. So far, PHANTOMLEAF® products have been supplied exclusively to special military and police units in Germany and abroad. There, their effectiveness has been proven in action. Due to the great demand, PHANTOMLEAF® has decided to also offer camouflage patterns for free sale The result is the WASP II camouflage pattern, which combines an exclusive look with breakthrough camouflage quality Unique silhouette breaking. In combination with complex structural algorithms Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distances, against a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This greatly expands the user's scope of action. PHANTOMLEAF® has developed a consistently modular system of camouflage schemes that are coordinated with each other and with worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grassland and scrubland, and in places rock and scree. WASP II in color variant Z3A (high growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forest but also tropical jungle with a high adaptability for border areas, such as scrub and agricultural land or grass zones. WASP II in color variant Z3b (high growth with snow cover) for application in regions with vegetation and rock and an interrupted snow cover. WASP II in color variant Z4 (construction) for use in human-altered environments ranging from urban terrain to large vehicles such as ships, airplanes and trains to special scenarios such as oil rigs. 100% made in Germany.   Material:Netzmaterial 100% Polyester (inhärent FR PES).   

With the PHANTOMLEAF® PYTHON BACKPACK COVER G1, backpacks up to approx. 120 liters or objects of a similar size can be camouflaged in a flash. Thanks to its circumferential adjustable elastic band, it sits firmly all around. It can also be used as a pack sack for the PYTHON net camouflage products. With the camouflage loops, 3D elements (PHANTOMLEAF® PYTHON LEAVES #430180) can be attached quickly. Details: 6 loops for attaching camouflage material. Circumferential elastic band with pull stopper. Size L-XL for backpacks up to 120 L (e.g. Berghaus Atlas with side pockets). Weight: approx. 175 g (size L-XL). Note: The leaf imitations are not included in the scope of delivery! The illustration only shows an application example. PHANTOMLEAF® has developed a new type of mesh material especially for the needs of Special Forces: the PYTHON product line. The target points were: Complete camouflage in the visual and near infrared regions of the electromagnetic spectrum. Reduced gloss level and low noise. Inherently flame retardant. Very tear-resistant and tightly woven: less entanglement in thorns and a barrier against vectors (disease-transmitting organisms). Extra light and small in pack size. Low water absorption and quick drying. So far, the PHANTOMLEAF® products have only been supplied to special units in the military and police at home and abroad. Their effect has been proven in action there. Due to the diverse demand, PHANTOMLEAF® has decided to also offer camouflage patterns for sale. The result is the WASP II camouflage pattern, which combines an exclusive look with striking camouflage quality: Unique breaking of the silhouette. In combination with complex structural algorithms. Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distance and this in front of a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This considerably expands the user's freedom of action. PHANTOMLEAF® has developed a system of camouflage schemes that is consistently modular and coordinated for worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grass and scrubland and in places rock and scree. WASP II in the color variant Z3A (tall growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forests, but also tropical jungles with a high level of adaptability for border areas such as bush and agricultural land or grass zones. WASP II in color variant Z3b (tall stature with snow cover) for use in regions with vegetation and rocks and an interrupted snow cover. WASP II in the color variant Z4 (construction) for use in humanly changed surroundings from urban terrain to large vehicles such as ships, aircraft and trains to special scenarios such as drilling rigs. 100% made in Germany.   Material:Netzmaterial 100% Polyester (inhärent FR PES).   

With the PHANTOMLEAF® PYTHON BACKPACK COVER G2, backpacks up to approx. 120 liters or items of similar size can be covered in a flash. Due to its circumferential adjustable elastic band, it fits tightly all around. It can also be used as a pack sack for the PYTHON net camouflage products By applying our specially developed slit tape, any 3D elements such as the PYTHON LEAVES G1 but also all other individual shapes and colors as well as natural vegetation can be combined. This allows the user to adapt the PYTHON BACKPACK COVER G2 almost limitlessly and quickly for his application space and quickly achieve his optimized solution Details: Slash band for attaching camouflage material. Circumferential elastic with pull stopper. Size L-XL for backpacks up to 120 L (e.g. Berghaus Atlas with side pockets).... Weight: approx. 180 g (size S-M). Note: The imitation leaves #430180 are not included! The picture shows only an example of use. Especially for the needs of special forces PHANTOMLEAF® has developed a new type of mesh material: The PYTHON product line. Target points were: Complete camouflage in the visual range and near-infrared range of the electromagnetic spectrum. Reduced gloss and low noise. Inherently flame retardant. Very tear resistant and tightly woven: less entanglement in thorns and barrier to vectors (disease-carrying creatures). At the same time extra light and small in pack size. Low water absorption and quick drying. So far, PHANTOMLEAF® products have been supplied exclusively to special military and police units in Germany and abroad. There, their effectiveness has been proven in action. Due to the great demand, PHANTOMLEAF® has decided to also offer camouflage patterns for free sale. The result is the WASP II camouflage pattern, which combines an exclusive look with breakthrough camouflage quality: Unique silhouette breaking. In combination with complex structural algorithms. Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distances, against a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This greatly expands the user's scope of action. PHANTOMLEAF® has developed a consistently modular system of camouflage schemes that are coordinated with each other and with worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grassland and scrubland, and in places rock and scree. WASP II in color variant Z3A (high growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forest but also tropical jungle with a high adaptability for border areas, such as scrub and agricultural land or grass zones. WASP II in color variant Z3b (high growth with snow cover) for application in regions with vegetation and rock and an interrupted snow cover. WASP II in color variant Z4 (construction) for use in human-altered environments ranging from urban terrain to large vehicles such as ships, airplanes and trains to special scenarios such as oil rigs. 100% made in Germany.   Material:Netzmaterial 100% Polyester (inhärent FR PES).   

With the PHANTOMLEAF® PYTHON BACKPACK COVER G2, backpacks up to approx. 60 liters or items of similar size can be covered in a flash. Due to its circumferential adjustable elastic band, it fits tightly all around. It can also be used as a pack sack for the PYTHON net camouflage products By applying our specially developed slit tape, any 3D elements such as the PYTHON LEAVES G1 but also all other individual shapes and colors as well as natural vegetation can be combined. This allows the user to adapt the PYTHON BACKPACK COVER G2  almost limitlessly and quickly for his application space and quickly achieve his optimized solution Details: Slash strap for attaching camouflage material. Circumferential elastic band with pull stopper. Size S-M for backpacks up to 60 L (e.g. Berghaus Munro, Berghaus Centurio). Weight: approx. 105 g (size S-M). Note: The imitation leaves are not included! The picture only shows an example of use. PHANTOMLEAF® has developed a new type of mesh material especially for the needs of special forces: The PYTHON product line. Target points were: Complete camouflage in the visual range and near-infrared range of the electromagnetic spectrum. Reduced gloss and low noise. Inherently flame retardant. Very tear resistant and tightly woven: less entanglement in thorns and barrier to vectors (disease-carrying creatures). At the same time extra light and small in pack size. Low water absorption and quick drying. So far, PHANTOMLEAF® products have been supplied exclusively to special military and police units in Germany and abroad. There, their effectiveness has been proven in action. Due to the great demand, PHANTOMLEAF® has decided to also offer camouflage patterns for free sale. The result is the WASP II camouflage pattern, which combines an exclusive look with breakthrough camouflage quality: Unique silhouette breaking. In combination with complex structural algorithms. Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distances, against a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This greatly expands the user's scope of action. PHANTOMLEAF® has developed a consistently modular system of camouflage schemes that are coordinated with each other and with worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grassland and scrubland, and in places rock and scree. WASP II in color variant Z3A (high growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forest but also tropical jungle with a high adaptability for border areas, such as scrub and agricultural land or grass zones. WASP II in color variant Z3b (high growth with snow cover) for application in regions with vegetation and rock and an interrupted snow cover. WASP II in color variant Z4 (construction) for use in human-altered environments ranging from urban terrain to large vehicles such as ships, airplanes and trains to special scenarios such as oil rigs. 100% made in Germany.   Material:Netzmaterial 100% Polyester (inhärent FR PES).   

The PHANTOMLEAF® PYTHON BALACLAVA G1 balaclava has some very practical features: On the one hand, it is "one size", but it can be individually optimally adjusted using anatomically adapted elastic cords so that it fits perfectly. It has a short shield over the eyes: This means that the eye area is in the shadow. The viewing slit is contoured so that on the one hand it completely covers particularly conspicuous areas such as the bridge of the nose and cheekbones, on the other hand it does not hinder peripheral vision. Using camouflage loops, 3D elements (PHANTOMLEAF® PYTHON LEAVES #430180) can be attached to the top so that the telltale head shape is optimally broken up. Optimal hearing is possible thanks to the quiet and very permeable mesh material. Details: 4 loops for attaching camouflage material. Anatomically adapted elastic cords for a perfect fit. Short shield over the eyes. Quiet and very permeable mesh material enables optimal hearing. Weight: approx. 90 g. Note: The leaf imitations are not included in the scope of delivery! The illustration only shows an application example. PHANTOMLEAF® has developed a new type of mesh material especially for the needs of Special Forces: the PYTHON product line. The target points were: Complete camouflage in the visual and near infrared regions of the electromagnetic spectrum. Reduced gloss level and low noise. Inherently flame retardant. Very tear-resistant and tightly woven: less entanglement in thorns and a barrier against vectors (disease-transmitting organisms). Extra light and small in pack size. Low water absorption and quick drying. So far, the PHANTOMLEAF® products have only been supplied to special units in the military and police at home and abroad. Their effect has been proven in action there. Due to the diverse demand, PHANTOMLEAF® has decided to also offer camouflage patterns for sale. The result is the WASP II camouflage pattern, which combines an exclusive look with striking camouflage quality: Unique breaking of the silhouette. In combination with complex structural algorithms. Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distance and this in front of a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This considerably expands the user's freedom of action. PHANTOMLEAF® has developed a system of camouflage schemes that is consistently modular and coordinated for worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grass and scrubland and in places rock and scree. WASP II in the color variant Z3A (tall growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forests, but also tropical jungles with a high level of adaptability for border areas such as bush and agricultural land or grass zones. WASP II in color variant Z3b (tall stature with snow cover) for use in regions with vegetation and rocks and an interrupted snow cover. WASP II in the color variant Z4 (construction) for use in humanly changed surroundings from urban terrain to large vehicles such as ships, aircraft and trains to special scenarios such as drilling rigs. Made in Germany.   Material:Netzmaterial: 100% Polyester (inhärent FR PES).   

The PHANTOMLEAF® PYTHON BOONIE REVERSIBLE G1 is fully reversible from WASP Z2 to Z3a. The outer edges of the brim are made extra contour-breaking with a scalloped edge, which minimizes telltale drop shadows. The PYTHON BOONIE REVERSIBLE G1 has camouflage loops on the crown and all around. The camo loops allow 3D elements (PHANTOMLEAF® PYTHON LEAVES imitation leaf #430180) to be quickly attached. Details: Reversible from WASP Z2 to Z3a. All-around camouflage loops. Camouflage loops on crown. Rounded cut edges to minimize drop shadows. Elastic drawstring with cord stopper. Weight: approx. 90 g (size S-M). Note: Imitation leaves #430180 are not included! PHANTOMLEAF® has developed a new type of mesh material especially for the needs of special forces: The PYTHON product line. Target points were: Complete camouflage in the visual range and near infrared range of the electromagnetic spectrum. Reduced gloss and low noise. Inherently flame retardant. Very tear resistant and tightly woven: less entanglement in thorns and barrier to vectors (disease-carrying creatures). At the same time extra light and small in pack size. Low water absorption and quick drying. So far, PHANTOMLEAF® products have been supplied exclusively to special military and police units in Germany and abroad. There, their effectiveness has been proven in action. Due to the great demand, PHANTOMLEAF® has decided to also offer camouflage patterns for free sale The result is the WASP II camouflage pattern, which combines an exclusive look with breakthrough camouflage quality Unique silhouette breaking. In combination with complex structural algorithms Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distances, against a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This greatly expands the user's scope of action. PHANTOMLEAF® has developed a consistently modular system of camouflage schemes that are coordinated with each other and with worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grassland and scrubland, and in places rock and scree. WASP II in color variant Z3A (high growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forest but also tropical jungle with a high adaptability for border areas, such as scrub and agricultural land or grass zones. WASP II in color variant Z3b (high growth with snow cover) for application in regions with vegetation and rock and an interrupted snow cover. WASP II in color variant Z4 (construction) for use in human-altered environments ranging from urban terrain to large vehicles such as ships, airplanes and trains to special scenarios such as oil rigs. Made in Germany.   Material:Netzmaterial: 100% Polyester (inhärent FR PES).   

The feet are very characteristic parts of the human body. With the PHANTOMLEAF® PYTHON BOOT COVER G2 you can make your feet as indistinct as possible by making them difficult to recognize. If you sew on 3D elements (PHANTOMLEAF® PYTHON LEAVES #430180) individually, the effect is increased. The BOOT COVER G2 has a button loop on the front and back to attach it to the PHANTOMLEAF® gaiters and suits, and an elastic drawstring for a secure fit. The BOOT COVER G2 can also be used to camouflage a variety of objects, such as Cameras, small bags, etc. Details: Button loops for attachment to gaiters and suits. Elastic drawstring for a secure and tight fit. Weight: approx. 110 g / pair. PHANTOMLEAF® has developed a new type of mesh material especially for the needs of Special Forces: the PYTHON product line. The target points were: Complete camouflage in the visual and near infrared regions of the electromagnetic spectrum. Reduced gloss level and low noise. Inherently flame retardant. Very tear-resistant and tightly woven: less entanglement in thorns and a barrier against vectors (disease-transmitting organisms). Extra light and small in pack size. Low water absorption and quick drying. So far, the PHANTOMLEAF® products have only been supplied to special units in the military and police at home and abroad. Their effect has been proven in action there. Due to the diverse demand, PHANTOMLEAF® has decided to also offer camouflage patterns for sale. The result is the WASP II camouflage pattern, which combines an exclusive look with striking camouflage quality: Unique breaking of the silhouette. In combination with complex structural algorithms. Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distance and this in front of a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This considerably expands the user's freedom of action. PHANTOMLEAF® has developed a system of camouflage schemes that is consistently modular and coordinated for worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grass and scrubland and in places rock and scree. WASP II in the color variant Z3A (tall growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forests, but also tropical jungles with a high level of adaptability for border areas such as bush and agricultural land or grass zones. WASP II in color variant Z3b (tall stature with snow cover) for use in regions with vegetation and rocks and an interrupted snow cover. WASP II in the color variant Z4 (construction) for use in humanly changed surroundings from urban terrain to large vehicles such as ships, aircraft and trains to special scenarios such as drilling rigs. 100% made in Germany.   Material:Netzmaterial 100% Polyester (inhärent FR PES).   

The PHANTOMLEAF® PYTHON GAUNTLETS G1 hand covers have it all: They can be individually adjusted using elastic bands. This means that they are firmly clamped between the middle finger and wrist and do not slip. The width adjustment means that they can also be worn with or without gloves. A small tab allows it to be taken off and put on quickly. The highlight: With the hand covers it is possible to camouflage the gloves in different colors in a flash and the hand cover simply remains on the glove when taking off and putting on. Details: Individually adjustable with elastic cords. Can be worn with or without gloves. Small tab for quick undressing and undressing. One size. Weight: approx. 40 g / pair. Note: The gloves are not included. The illustrations only show an application example. PHANTOMLEAF® has developed a new type of mesh material especially for the needs of Special Forces: the PYTHON product line. The target points were: Complete camouflage in the visual and near infrared regions of the electromagnetic spectrum. Reduced gloss level and low noise. Inherently flame retardant. Very tear-resistant and tightly woven: less entanglement in thorns and a barrier against vectors (disease-transmitting organisms). Extra light and small in pack size. Low water absorption and quick drying. So far, the PHANTOMLEAF® products have only been supplied to special units in the military and police at home and abroad. Their effect has been proven in action there. Due to the diverse demand, PHANTOMLEAF® has decided to also offer camouflage patterns for sale. The result is the WASP II camouflage pattern, which combines an exclusive look with striking camouflage quality: Unique breaking of the silhouette. In combination with complex structural algorithms. Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distance and this in front of a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This considerably expands the user's freedom of action. PHANTOMLEAF® has developed a system of camouflage schemes that is consistently modular and coordinated for worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grass and scrubland and in places rock and scree. WASP II in the color variant Z3A (tall growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forests, but also tropical jungles with a high level of adaptability for border areas such as bush and agricultural land or grass zones. WASP II in color variant Z3b (tall stature with snow cover) for use in regions with vegetation and rocks and an interrupted snow cover. WASP II in the color variant Z4 (construction) for use in humanly changed surroundings from urban terrain to large vehicles such as ships, aircraft and trains to special scenarios such as drilling rigs. 100% made in Germany.   Material:Netzmaterial: 100% Polyester (inhärent FR PES).   

When developing the PHANTOMLEAF® PYTHON LEAVES 3D leaf imitations, various aspects had to be taken into account: On the one hand, large volume and thus a maximum 3D effect should be created and in a natural-looking shape, on the other hand, entanglement in vegetation should be reduced as much as possible. The aim was to give the user the opportunity to change the 3D elements very quickly and thus optimally adapt to his current application scenario. They can be knotted individually to match the basic pattern in the articles in the specially developed slit tape and camouflage loops. The leaf imitations are particularly suitable for scenarios with a leafy environment. In contrast to many other products, both sides of the leaf imitations are printed. This means that there are no noticeable "speed cameras" when the 3D element rotates in motion. Different colors, e.g. Mix Z2, Z3a and Z4 and also mix in the PYTHON THREADS. There are no limits to creativity here! Important NOTE: In order to get the optimal camouflage result, please always use the leaf imitations that match the basic color of the product that is equipped with it in the appropriate place: Mainly light green imitation leaves on mainly light green product areas, mainly dark brown imitation leaves on mainly dark brown product areas! Scope of delivery: 10 individual sheet imitations. Weight: approx. 30 g / set of 10. PHANTOMLEAF® has developed a new type of mesh material especially for the needs of Special Forces: the PYTHON product line. The target points were: Complete camouflage in the visual and near infrared regions of the electromagnetic spectrum. Reduced gloss level and low noise. Inherently flame retardant. Very tear-resistant and tightly woven: less entanglement in thorns and a barrier against vectors (disease-transmitting organisms). Extra light and small in pack size. Low water absorption and quick drying. So far, the PHANTOMLEAF® products have only been supplied to special units in the military and police at home and abroad. Their effect has been proven in action there. Due to the diverse demand, PHANTOMLEAF® has decided to also offer camouflage patterns for sale. The result is the WASP II camouflage pattern, which combines an exclusive look with striking camouflage quality: Unique breaking of the silhouette. In combination with complex structural algorithms. Targeted manipulation of human perception based on medical expertise. As a result, the object to be camouflaged is much more difficult to detect from close to distant distance and this in front of a variety of backgrounds such as grass, dry branches, leaves in different colors and brightnesses of an operational area (see camouflage pattern zones below). This considerably expands the user's freedom of action. PHANTOMLEAF® has developed a system of camouflage schemes that is consistently modular and coordinated for worldwide use: WASP II in color variant Z2 (low growth) for regions with low-growing vegetation, such as grass and scrubland and in places rock and scree. WASP II in the color variant Z3A (tall growth without snow cover) for use in areas with high vegetation, such as deciduous and coniferous forests, but also tropical jungles with a high level of adaptability for border areas such as bush and agricultural land or grass zones. WASP II in color variant Z3b (tall stature with snow cover) for use in regions with vegetation and rocks and an interrupted snow cover. WASP II in the color variant Z4 (construction) for use in humanly changed surroundings from urban terrain to large vehicles such as ships, aircraft and trains to special scenarios such as drilling rigs. 100% made in Germany.   Material:  Netzmaterial 100% Polyester (inhärent FR PES).